Page 1 of 4 1 2 3 ... LastLast
Threads 1 to 20 of 77

Forum: Career and Advice Forum

Do you have questions about how to get into the industry, salaries, where to go to school, new to this site, or any other just getting started question, ask here. Moderated by: support.

  1. Post Inventor: how easy is it to pick up

    Started by sjh, January 29th, 2017 03:11 PM
    inventor, training
    • Replies: 0
    • Views: 2,384
    January 29th, 2017, 03:11 PM Go to last post
  2. Free web hosting for community ;)

    Started by Webbera, January 26th, 2017 12:15 PM
    free web hosting, web hosting
    • Replies: 0
    • Views: 483
    January 26th, 2017, 12:15 PM Go to last post
    • Replies: 0
    • Views: 612
    December 22nd, 2016, 03:30 AM Go to last post
  3. Get your Electro-Mechanical Design Right

    Started by prashantshelke, December 22nd, 2016 03:25 AM
    design for manufacturing, dfm, electronic manufacturing
    • Replies: 0
    • Views: 504
    December 22nd, 2016, 03:25 AM Go to last post
    • Replies: 0
    • Views: 790
    November 22nd, 2016, 03:37 AM Go to last post
  4. Best way to study further in Catia V5

    Started by Achroatic, November 12th, 2016 07:01 PM
    • Replies: 5
    • Views: 936
    November 15th, 2016, 05:49 PM Go to last post
  5. How to Avoid Sink Marks in Plastic Part Design?

    Started by prashantshelke, October 10th, 2016 03:10 AM
    • Replies: 0
    • Views: 723
    October 10th, 2016, 03:10 AM Go to last post
  6. Advice for a 3D Artist

    Started by Thatcher, October 8th, 2016 12:34 PM
    • Replies: 0
    • Views: 294
    October 8th, 2016, 12:34 PM Go to last post
  7. Design for Standardization

    Started by prashantshelke, August 1st, 2016 01:27 AM
    • Replies: 0
    • Views: 1,185
    August 1st, 2016, 01:27 AM Go to last post
  8. Dirt Cheap CAD software

    Started by zkbuck, September 17th, 2013 12:02 AM
    • Replies: 3
    • Views: 7,571
    July 26th, 2016, 01:16 AM Go to last post
    • Replies: 0
    • Views: 564
    July 22nd, 2016, 06:51 AM Go to last post
    • Replies: 0
    • Views: 525
    July 22nd, 2016, 06:46 AM Go to last post
  9. Need open source or low cost CAD recommendations

    Started by awfulwaffle, July 17th, 2016 05:13 PM
    • Replies: 0
    • Views: 436
    July 17th, 2016, 05:13 PM Go to last post
  10. Dyslexics learning CAD packages

    Started by LewiH, June 29th, 2016 03:15 PM
    • Replies: 0
    • Views: 587
    June 29th, 2016, 03:15 PM Go to last post
    • Replies: 0
    • Views: 2,547
    April 2nd, 2016, 02:14 AM Go to last post
  11. Design for Performance

    Started by prashantshelke, October 29th, 2015 06:04 AM
    • Replies: 0
    • Views: 4,262
    October 29th, 2015, 06:04 AM Go to last post
  12. Exclamation Help deciding CAD software for beginner

    Started by mohala, July 16th, 2015 12:42 PM
    • Replies: 0
    • Views: 2,946
    July 16th, 2015, 12:42 PM Go to last post
    • Replies: 0
    • Views: 1,764
    July 9th, 2015, 07:18 AM Go to last post
    • Replies: 0
    • Views: 2,042
    July 7th, 2015, 07:07 AM Go to last post
  13. SpaceMouse vs Spacecontroller ?

    Started by skan, October 5th, 2014 11:47 AM
    • Replies: 0
    • Views: 4,735
    October 5th, 2014, 11:47 AM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread