Search:

Tag: sketch

Search: Search took 0.00 seconds; generated 2 minute(s) ago.

  1. Fully Constrained & Under Constrained

    Started by araminaran, January 18th, 2020 02:18 AM
    constraint, sketch
    • Replies: 3
    • Views: 478
    Last Post: February 1st, 2020 08:52 PM
    by MTLian  Go to last post

    Forum:
    CATIA Forum

  2. Problem with snapping in part sketch

    Started by PanSam, January 18th, 2020 03:00 PM
    loft, sketch, snap
    • Replies: 0
    • Views: 442
    Last Post: January 18th, 2020 03:00 PM
    by PanSam  Go to last post
  3. 7-Tips Sketcher Part Design - CATIA R19x

    Started by PLM Technology, May 13th, 2019 02:19 AM
    3dexperience, catia, part design, sketch, tips
    • Replies: 2
    • Views: 2,747
    Last Post: May 13th, 2019 08:55 AM
    by PLM Technology  Go to last post

    Forum:
    CATIA Forum

  4. CATIA publication replace

    Started by spe88, August 30th, 2018 06:25 AM
    catia, publication, reference, replace, sketch
    • Replies: 2
    • Views: 1,955
    Last Post: August 31st, 2018 01:42 AM
    by spe88  Go to last post

    Forum:
    CATIA Forum

  5. Error Using Sketches Under Feature - Help Needed

    Started by GCarnes, February 27th, 2017 02:21 PM
    error, feature, rib, sketch
    • Replies: 2
    • Views: 3,498
    Last Post: February 27th, 2017 04:23 PM
    by GCarnes  Go to last post

    Forum:
    CATIA Forum

    • Replies: 2
    • Views: 11,033
    Last Post: December 20th, 2016 09:56 AM
    by piendelb  Go to last post

    Forum:
    CATIA Forum

  6. Why shouldnt we use sketch in NX ?

    Started by wowpilot, August 30th, 2016 04:54 AM
    sketch, unigraphics
    • Replies: 1
    • Views: 3,267
    Last Post: October 2nd, 2016 12:29 PM
    by M4573RMZD  Go to last post

    Forum:
    UG/NX Forum

    • Replies: 1
    • Views: 3,224
    Last Post: February 22nd, 2016 12:53 AM
    by MrCATIA  Go to last post

    Forum:
    CATIA Forum

    • Replies: 5
    • Views: 10,052
    Last Post: January 6th, 2016 03:26 PM
    by anunzul  Go to last post

    Forum:
    CATIA Forum

  7. Negative length in sketch NX7.5.5?

    Started by spacely, March 11th, 2014 09:09 AM
    length, sketch
    • Replies: 2
    • Views: 6,652
    Last Post: December 27th, 2014 12:48 AM
    by jay mittal  Go to last post

    Forum:
    UG/NX Forum

  8. Gear Sketch Generator

    Started by SolidMaster, September 2nd, 2014 10:51 PM
    gear, involute, sketch, toolbox
    • Replies: 1
    • Views: 12,577
    Last Post: October 31st, 2014 01:47 PM
    by abert  Go to last post
  9. Creating Weldment Profile with Multiple Sketch Blocks

    Started by C4SEM4N, September 29th, 2014 09:55 AM
    • Replies: 0
    • Views: 3,821
    Last Post: September 29th, 2014 09:55 AM
    by C4SEM4N  Go to last post
Results 1 to 12 of 12